U.S. PHARMACOPEIA

Search USP29  
Ranitidine Tablets
» Ranitidine Tablets contain an amount of ranitidine hydrochloride (C13H22N4O3S·HCl) equivalent to not less than 90.0 percent and not more than 110.0 percent of the labeled amount of ranitidine (C13H22N4O3S).
Packaging and storage— Preserve in tight, light-resistant containers.
Identification—
A: The RF value of the principal spot observed in the chromatogram of the Test preparation obtained as directed in the Chromatographic purity test corresponds to that obtained from the Standard preparation.
B: The retention time of the major peak in the chromatogram of the Assay preparation corresponds to that of the major peak in the chromatogram of the Standard preparation as obtained in the Assay.
C: Shake a quantity of crushed Tablets, equivalent to about 100 mg of ranitidine, with 2 mL of water, and filter: the filtrate responds to the tests for Chloride 191.
Dissolution 711
Medium: water; 900 mL.
Apparatus 2: 50 rpm.
Time: 45 minutes.
Procedure— Determine the amount of C13H22N4O3S dissolved from UV absorbances at the wavelength of maximum absorbance at about 314 nm using filtered portions of the solution under test, suitably diluted with water, if necessary, in comparison with a Standard solution having a known concentration of USP Ranitidine Hydrochloride RS in the same medium.
Tolerances— Not less than 80% (Q) of the labeled amount of C13H22N4O3S is dissolved in 45 minutes.
Uniformity of dosage units 905: meet the requirements.
Chromatographic purity—
Test preparation— Prepare a filtered solution in methanol containing 20 mg of ranitidine per mL (equivalent to 22.4 mg of ranitidine hydrochloride per mL) by shaking an appropriate number of Tablets in a suitable volume of methanol until the tablets have disintegrated completely.
Standard preparations— Dissolve USP Ranitidine Hydrochloride RS in methanol to obtain a solution having a known concentration of 0.22 mg per mL. Dilute portions of this Standard preparation quantitatively with methanol to obtain solutions having concentrations of 110 µg per mL (Diluted standard preparation A), 66 µg per mL (Diluted standard preparation B), 22 µg per mL (Diluted standard preparation C), and 11 µg per mL (Diluted standard preparation D), respectively.
Resolution preparation— Dissolve USP Ranitidine Related Compound A RS, 5-[[(2-aminoethyl)thio]methyl]-N,N-dimethyl-2-furanmethanamine, hemifumarate salt, in methanol to obtain a solution having a known concentration of 1.27 mg per mL.
Procedure— Apply separately 10 µL of the Test preparation, the Standard preparation, and Diluted standard preparations A, B, C, and D to a suitable thin-layer chromatographic plate (see Chromatography 621) coated with a 0.25-mm layer of chromatographic silica gel mixture. In addition, apply separately 10 µL of the Test preparation to the same plate, and on top of this application, apply 10 µL of the Resolution preparation. Allow the spots to dry, and develop the chromatograms in a solvent system consisting of a mixture of ethyl acetate, isopropyl alcohol, ammonium hydroxide, and water (25:15:5:1) until the solvent front has moved not less than 15 cm from the origin. Remove the plate from the developing chamber, mark the solvent front, and air-dry. Expose the plate to iodine vapor in a closed chamber until the chromatogram is fully revealed. Examine the plate, and compare the intensities of any secondary spots observed in the chromatogram of the Test preparation with those of the principal spots in the chromatograms of the Standard preparation and Diluted standard preparations A, B, C, and D: the system suitability requirements are met if there is complete resolution between the primary spots in the chromatogram of the combined Test preparation and the Resolution preparation, and if a spot is observed in the chromatogram of Diluted standard preparation D. No single secondary spot exhibits an intensity greater than that of Diluted standard preparation A (0.5%), and no other secondary spot exhibits an intensity greater than that of Diluted standard preparation B (0.3%). The sum of the intensities of all secondary spots obtained from the Test preparation correspond to not more than 2.0%.
Residual solvents 467: meet the requirements.
(Official January 1, 2007)
Assay—
Mobile phase, Standard preparation, System suitability solution, and Chromatographic system Prepare as directed in the Assay under Ranitidine Hydrochloride.
Assay preparation— Transfer 10 Tablets to a minimum of 250 mL of Mobile phase, accurately measured. Shake the mixture until the Tablets have disintegrated completely, and filter. Dilute the filtrate quantitatively, and stepwise if necessary, with Mobile phase to obtain a solution having a concentration of ranitidine similar to that of the Standard preparation.
Procedure— Separately inject equal volumes (about 10 µL) of the Standard preparation and the Assay preparation into the chromatograph, record the chromatograms, and measure the area responses for the major peaks. Calculate the quantity, in mg, of C13H22N4O3S in the portion of Tablets taken by the formula:
(314.40 / 350.87)(L / D)(C)(rU / rS),
in which 314.40 and 350.87 are the molecular weights of ranitidine and ranitidine hydrochloride, respectively; L is the labeled amount, in mg, of ranitidine in each tablet; D is the concentration, in mg per mL, of ranitidine in the Assay preparation, based on the labeled quantity per Tablet and the extent of dilution; C is the concentration, in mg per mL, of USP Ranitidine Hydrochloride RS in the Standard preparation; and rU and rS are the peak area responses obtained from the Assay preparation and the Standard preparation, respectively.
Auxiliary Information— Staff Liaison : Elena Gonikberg, Ph.D., Scientist
Expert Committee : (MDGRE05) Monograph Development-Gastrointestinal Renal and Endocrine
USP29–NF24 Page 1893
Phone Number : 1-301-816-8251